Sorry your browser is not supported!

You are using an outdated browser that does not support modern web technologies, in order to use this site please update to a new browser.

Browsers supported include Chrome, FireFox, Safari, Opera, Internet Explorer 10+ or Microsoft Edge.

DarkBASIC Professional Discussion / dll problem

Author
Message
stormtrooper
23
Years of Service
User Offline
Joined: 24th Nov 2002
Location: United States
Posted: 12th Dec 2002 03:40
Link
Can anyone answer this? This pops up when I try to run some code, ( command in DLL command-table unrecognised (message box %s% messagebox popup). I just got a new system, Dell p4 1.8 Gig 128 meg ddr sdram, 32 meg ati rage ultra 4x agp video card and windows xp home ed. I did reinstall DBP and then tried to run some code off my old drive and got this message so then I typed this into the editor to see if it would run

do
print "hello world"
loop

it did run after I clicked ok in the messagebox
this did not happen on my old system or with the old code I had on my old drive
any answers????
Back to top
Profile PM Email
G Man X
23
Years of Service
User Offline
Joined: 11th Dec 2002
Location:
Posted: 12th Dec 2002 23:23
Link
I get the same message. Mine no longer runs at all.
Windows 4.10.1998 PIII 450, 768MBRAM. A simple mesh with a sphere type ting. Had no problems running this code in DB and none in DBPro Demo. This is a system-level thing, I suspect. Can anyone tell me where to go to raise system-level issues?

Good The Boyz Have Done It Is!
Back to top
Profile PM
stormtrooper
23
Years of Service
User Offline
Joined: 24th Nov 2002
Location: United States
Posted: 13th Dec 2002 01:17
Link
I'm going to run windows xp in classic windows mode to see what happens, I doubt if it will change anything

Back to top
Profile PM Email
MrTAToad
23
Years of Service
User Offline
Joined: 26th Aug 2002
Location: United Kingdom
Posted: 13th Dec 2002 11:20
Link
It sounds like one of the compiler DLL's has been deleted/modified or corrupted - try re-installing.

Good news everybody! I really am THAT good...
Back to top
Profile PM Email Website
G Man X
23
Years of Service
User Offline
Joined: 11th Dec 2002
Location:
Posted: 15th Dec 2002 13:27
Link
Reinstalled. It's working. Hooray

Good The Boyz Have Done It Is!
Back to top
Profile PM
stormtrooper
23
Years of Service
User Offline
Joined: 24th Nov 2002
Location: United States
Posted: 15th Dec 2002 22:38
Link
I tried reinstalling and the program worked until I installed patch 3.1 then the same thing happened

Back to top
Profile PM Email
MrTAToad
23
Years of Service
User Offline
Joined: 26th Aug 2002
Location: United Kingdom
Posted: 15th Dec 2002 23:34
Link
Sounds like your download of P3.1 is invalid or you've got a dodgy sector on your hard drive.

Good news everybody! I really am THAT good...
Back to top
Profile PM Email Website
stormtrooper
23
Years of Service
User Offline
Joined: 24th Nov 2002
Location: United States
Posted: 18th Dec 2002 16:13
Link
I have reinstalled DBP and reinstalled patch 3.1 after I deleated it from my system and redownloaded it. It still caused this error so I reinstalled DBP and patch 2 ran fine. Reinstalled DBP and P3 and this error came up. If all of your are working these patches could conflict with my system but I can't figure out how! I hope patch 4 does not do this!!!

Back to top
Profile PM Email
MrTAToad
23
Years of Service
User Offline
Joined: 26th Aug 2002
Location: United Kingdom
Posted: 18th Dec 2002 23:45
Link
I suspect one of the dll's isn't being installed correctly - possible due to bad clusters etc.

Without deleting the current installation (and re-naming it), try re-installing it again (so it uses a different set of clusters)

Good news everybody! I really am THAT good...
Back to top
Profile PM Email Website
Back to top

Login to post a reply

Server time is: 2026-07-04 13:05:13
Your offset time is: 2026-07-04 13:05:13